Introduction
The JLab Go Air Pop is a popular choice for budget-conscious consumers seeking quality wireless earbuds. Known for its affordability, comfortable fit, and solid performance, the Go Air Pop offers a compelling value proposition in the crowded wireless earbud market. This article provides a comprehensive guide to using the JLab Go Air Pop, covering everything from setup and pairing to troubleshooting and care.
Unboxing and Initial Setup
When you first receive your JLab Go Air Pop earbuds, you’ll find the following items in the box:
- JLab Go Air Pop wireless earbuds
- Charging case
- USB-C charging cable
- User manual
- (Optional) Extra ear tips in various sizes
Getting Started
- Charging the Earbuds and Case:
- Earbuds: Place the earbuds into the charging case. The earbuds will automatically begin charging when placed in the case.
- Charging Case: Connect the included USB-C charging cable to the charging case and plug it into a power source. A full charge typically takes about 1.5 hours.
- Powering On and Off:
- Power On: Remove the earbuds from the charging case. They will power on automatically and enter pairing mode.
- Power Off: Place the earbuds back in the charging case, and they will automatically power off and begin charging.
Pairing with Your Device
- Initial Pairing:
- Bluetooth Mode: After removing the earbuds from the charging case, they will enter Bluetooth pairing mode. You’ll see a blinking LED light indicating they are in pairing mode.
- Device Connection: On your smartphone or other Bluetooth-enabled device, go to the Bluetooth settings and look for “JLab GO Air Pop” in the list of available devices. Tap on it to pair.
- Reconnecting:
- Once paired, the earbuds will automatically reconnect to the last device they were connected to when powered on and within range.
Using the Earbuds
- Controls:
- Play/Pause: Tap either earbud once.
- Volume Up: Tap the right earbud twice.
- Volume Down: Tap the left earbud twice.
- Next Track: Tap the right earbud three times.
- Previous Track: Tap the left earbud three times.
- Answer/End Call: Tap either earbud once.
- Reject Call: Tap and hold either earbud for 2 seconds.
- Activate Voice Assistant: Tap and hold either earbud for 2 seconds.
- Charging and Battery Life:
- Battery Indicator: The LED on the earbuds and the case will indicate the battery status. When the earbuds are charging, a red light will be displayed, and it will turn off once fully charged. The case’s LED indicator will show the charge level of the case itself.
Troubleshooting
- Earbuds Not Pairing:
- Ensure the earbuds are in pairing mode and within range of your device.
- If pairing fails, reset the earbuds by placing them in the case, closing the lid, then reopening it and attempting to pair again.
- Sound Issues:
- Check that the earbuds are properly seated in your ears and that there is no debris blocking the speaker.
- Ensure that the volume is turned up on both the earbuds and your device.
- One Earbud Not Working:
- Make sure both earbuds are fully charged.
- Re-seat the earbuds in the charging case to ensure proper charging and reset the connection by removing them from the case and pairing again.
Care and Maintenance
- Cleaning:
- Earbuds: Use a soft, dry cloth to clean the earbuds. Avoid getting moisture in the charging ports.
- Charging Case: Wipe the case with a damp cloth if needed, ensuring no water enters the charging port.
- Storage:
- Store the earbuds in their charging case when not in use to keep them protected and charged.
Conclusion
The JLab Go Air Pop offers an affordable and reliable option for those seeking wireless earbuds with good performance and ease of use. Following this manual will help you make the most out of your earbuds, ensuring a seamless and enjoyable audio experience. With proper setup, usage, and care, your JLab Go Air Pop earbuds will provide lasting performance and value.
